int(0)

Wall

I-DIAL INDOOR

I-Dial Indoor is a fully functional control unit designed to allow the user flexible management of the system. Its versatility makes it ideal for residential, sports, and municipal applications. It can control up to 12 solenoid valves with 4 programs and 1 start each. The easy 3 Easy Steps programming method allows you to adjust irrigation in just 60 seconds. In addition, the extra functions allow you to manage the rain sensor and pump in a comprehensive manner.

Technical information

Technical features

Controller type: Wall-mounted
Power supply: External transformer 220 VAC 50-60 Hz - 24 Volts AC, 0.8 AMP
Back-up battery: 2 alkaline batteries 1.5 volts (AA) not included
Rain sensor input
Pump/master valve control outlet
Backlit screen
Closing lid
Low battery signal
Maximum number of zones: 12
Models available: 4, 6, 8 and 12 zones

Standard Programming

Programming mode: Traditional
Number of programs: 4
Start times per program: 1
Maximum number of starts per day: 4
Minimum irrigation time per zone: 1 min
Maximum irrigation time per zone: 240 min
Irrigation frequency: By days of the week
Irrigation frequency: from once a day to every 15 days
Manual start: By zone
Reset button
Clear button
OFF function: Control unit
Seasonal adjustment from 10% to 200%
PUMP START Function
SENS START function

Pump Start

The Pump Start function allows you to program pump output activation on a zone-by-zone basis.

Sens Start

The Sens Start feature allows the rain sensor intervention to be programmed on a zone-by-zone basis.

Solenoid 24 Vac

The controllers control 24 Vac normally closed solenoids. The control unit will supply the solenoid with a 24 Vac electrical signal for the entire irrigation time to open the electrovalve.

3 Easy Steps

The special three-step programming feature allows for easy and intuitive programming in less than 60 seconds. The programming logic is based on answering three simple questions: what time of day to water, for how long, and how often.

One Look Display

The 3" backlit display shows you the full irrigation schedule at a glance. It is no longer necessary to navigate through various programming menus to see the irrigation schedule.

Code	Description	Barcode
200.4080410	I-DIAL 4 - 4 ZONES wall-mounted control unit	8015455571144
200.4080610	I-DIAL 6 - 6 ZONES wall-mounted control unit	8015455571168
200.4080810	I-DIAL 8 - 8 ZONES wall-mounted control unit	8058054002756
200.4081210	I-DIAL 12 -12 ZONES wall-mounted control unit	8058054006891
200.8500450	External 220V/24Vac transformer	8058054007065

	Code	Description	Barcode
TRS 220V/24 VAC		External transformer compatible with C-Dial and I-Dial control unit models

C-DIAL & I-DIAL

What is the difference between Programs and Zones?

Controllers programs identify an area or group of solenoid valves. Zones identify a specific solenoid valve.

How do I set the start time of the zones?

Irrigation controllers work by irrigation cycles distributed across programs. This means that it is not necessary to set the start time for all zones, but just set the start time of the irrigation cycle (program start time) and the watering times of the zones: the controller will open and close the solenoid valves in sequence.

I have programmed the I-Dial or C-Dial controller but it never irrigates.

Days of the week were probably not enabled during programming. Check that the days of the week in the Frequency menu are enabled (they have a frame around the day). If they are not active simply press the '+' key to enable the flashing day and move between days of the week with the 'enter' key.

The screen shows the umbrella icon but it has not rained.

Check that the two-wire rain sensor is correctly installed and is a normally closed rain sensor (Acqua Click model). If the rain sensor is not present, check that the metal bridge in the terminal compartment at "SENS" is present. In the case of an I-DIAL OUTDOOR control unit, check that the 220V mains connection has been made correctly (this operation requires a qualified electrician) and that an external 220/24 VAC transformer has not been installed.

Can I enable the rain sensor for single zones?

It's not possible to activate the rain sensor per zone with C-Dial. It's possible to activate the rain sensor per zone from the EXTRA functions with I-Dial.

Can I enable the rain sensor for single zones?

It's not possible to activate the rain sensor per zone with C-Dial. It's possible to activate the rain sensor per zone from the EXTRA functions with I-Dial.

When irrigation starts, the irrigation cycles are repeated twice in a row. How can I set only one daily cycle?

Check whether 2 start times or 2 schedules are active.

The control unit is properly powered but the screen indicates NoAC.

NoAC indicates that the circuit board is not receiving 24Vac. This situation can occur when the fuse or power supply is blown.

I-Dial - Istrucions and programming

Discover now: I-DIAL INDOOR for irrigation systems and transform your garden into a green oasis!